Installation Accesories

Blue Sea Terminal Block 30a 12 Circuit

Blue Sea Systems Terminal Block 30A - 12 CircuitModel: 2512-BSSClosed back design completely insulates power from the mounting surfaceEach screw pair is one isolated circuitJumpers allow creation of common circuitsSpecificationsCircuits12Length7.75in...

Newmar Ts2x8 Terminal Strip

Terminal Strips Use as a common negative/neutral bus for AC or DC systems. Dual terminal strips in 4 or 8 screw positions on 3/4? centers are secured to a high density insulated base. All hardware, bus material and fasteners are nickel-plated brass. #8...

Weld Mount 1.00"" Tall #8 X 32 Stainless Steel Stud 0.62"" Base 15 Pack

Wel Mount Stainless Studs (#8-32 thread) 1' tall 15 PackModel: 83216These small panel studs have a wide range of uses. Originally they were used for mounting on the backside of dash panels or for mounting to the console. Now they are used for securing a...

Weld Mount 0.75"" Tall #8 X 32 Stainless Steel Stud 0.62"" Base 15 Pack

Weld Mount Stainless Studs (#8-32 thread) .75"" tall 15 PackModel: 83212These small panel studs have a wide range of uses. Originally they were used for mounting on the backside of dash panels or for mounting to the console. Now they are used for...

Newmar Dx-3 Feed Thru

DX Series Feed-Thru Waterproof Fittings Provided with solid neoprene cable gland, installer drills holes and slits as required to accommodate cable with or without factory installed connector. Multiple cables may be passed through a single fitting. ...

Weld Mount At-5 Wire Tie Mount, Large Black 500 Pack

Weld Mount AT-5 Black Nylon Wire Tie Mount 500 PackModel: AT-5 (Black)The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of...

Weld Mount At-2010 Acrylic Adhesive 50ml

Weld Mount AT-2010 Acrylic AdhesiveModel: 2010AT-2010 is our biggest seller and is a unique adhesive. It has high viscosity and will hold smaller parts without sagging. Heavier parts may need our AT-690 fixture dots to hold parts in place while the...

Weld Mount 65100 Adhesively Bonded Fastener Kit

Weld Mount AT-65100Model: AT-65100The AT-65100 Adhesively Bonded Fastener Kit Has a Variety Of Weld Mount Parts Designed To Give The User The Chance To Try Our Weld Mount System At Low Cost.The Kit Comes With A Dispensing Gun And Mixing Tips For...

Newmar Cs-2 Connector Strip F/ 14g Wire

Molded nylon encases 6 or 12 pairs of connectors that use screw compression to secure wires without use of lugs. ideal for electronic installations. Brass barrels capture wires and are held in place with a stainless steel ?finger"" compressed by a screw...

Newmar Cs-1 Connector Strip F/ 16g Wire

Molded nylon encases 6 or 12 pairs of connectors that use screw compression to secure wires without use of lugs. ideal for electronic installations. Brass barrels capture wires and are held in place with a stainless steel ?finger"" compressed by a screw...

Weld Mount At-3 Wire Tie Mount, Small Black 30 Pack

Weld Mount AT-3 Black Nylon Wire Tie Mount 30 PackModel: 803BThe AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for a #3 wire tie with a maximum width of .20"". Average pull...

Weld Mount At-850 3.5"" Square Mixing Tip Pack Of 10 For At-2010, At-8040, At-4020

Weld Mount AT-850 Mixing Tip for AT-2010 and AT-8040 10 PackModel: 80850The At-850 tip is for use with AT-2010 and AT-8040. It’s unique design eliminates any possibility of the cartridge plugging up as the entry is separated.What's in the Box:10 AT-850...